|
|
|
|
| ABOVE GROUND SWIMMING POOL LINERS |
 |
 |
 |
| Anywhere ! |
 |
| OVERLAP LINERS |
 |
 |
 |
 |
 |
 |
 |
 |
| We suggest that 20mil is the best value |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
| EXPANDABLE OVERLAP LINERS |
 |
| Available in 60" and 72" Depth |
 |
|
|
|
|
|
|
|
 |
 |
| BEADED LINERS - 48" |
|
|
|
|
|
|
|
|
|
|
|
|
| BEADED LINERS - 52" |
|
|
|
|
|
|
|
|
|
|
| Overlap style Above Ground Pool Liners are installed under the top rail of the pool. If you have an overlap style liner, you can look under the top rail on the outside of the pool, and you will see the liner hanging down. |
| For a wrinkle free professional installation See Overlap Liner Installation Instructions provided below. |
| ABOVE GROUND POOL OVERLAP LINER REPLACEMENT INSTRUCTIONS: !. Completely drain pool. 2. Remove all wall fittings. (Skimmers and returns) 3. With a shrp knife, cut old liner directly below the top rails all the way around the pool. 4. Remove old liner from the pool. 5. Smooth pool floor and fill any depressions with sand. 5. Carefully remove new liner from box and spread it out on a clean dry surface, in order to let it warm up in the sun for at least 1 hour. 6. Drape new liner over the pool top rails in such a manner that only 3 or 4 feet of the liner is touching the center of the pool floor, and the liner seam is the same distance from the top rail all the way around the pool. 7. Tape the excess liner that is now draped over the outside of the pool wall to each of the upright support posts. 8. Start filling pool, and as the liner becomes taunt, slowly release a little of the liner at a time being carful to insure that the seam remains level alll the way around the pool. 9. Once the water is about 1/2 way up the side wall, remove two of the top rails at a time, remove the clips and the remaining piece of the old liner, and pull the new liner tight, attach the plastic coping strips, and re-attach the top rails. Proceed around the pool until complete. 10. Re-install the wall fittings when the water level is just a few inches below their intended location. NOTES: By allowing the water pressure to stretch the liner accros the pool floor should provide a smooth, wrinkle free bottom. It is suggested that you do not trim off the excess liner left on the outside of the pool wall, just fold it up under the top rail. |
| For a wrinkle free professional installation See Expandable Overlap Liner Installation Instructions provided below. |
| ABOVE GROUND POOL EXPANDABLE OVERLAP LINER REPLACEMENT INSTRUCTIONS: !. Completely drain pool. 2. Remove all wall fittings. (Skimmers and returns) 3. With a shrp knife, cut old liner directly below the top rails all the way around the pool. 4. Remove old liner from the pool. 5. Smooth pool floor and fill any depressions with sand. 5. Carefully remove new liner from box and spread it out on a clean dry surface, in order to let it warm up in the sun for at least 1 hour. 6. Drape new liner over the pool top rails in such a manner that only 3 or 4 feet of the liner is touching the pool floor, and the liner seam distance from the top rail IS ADJUSTED TO ALLOW FOR YOUR DEEP AREA. 7. Tape the excess liner that is now draped over the outside of the pool wall to each of the upright support posts. 8. Start filling pool, and as the liner becomes taunt, slowly release a little of the liner at a time being carful to insure that the seam remains level alll the way around the pool. 9. Once the water is about 1/2 way up the side wall, remove two of the top rails at a time, remove the clips and the remaining piece of the old liner, and pull the new liner tight, attach the plastic coping strips, and re-attach the top rails. Proceed around the pool until complete. 10. Re-install the wall fittings when the water level is just a few inches below their intended location. NOTES: By allowing the water pressure to stretch the liner accros the pool floor should provide a smooth, wrinkle free bottom. It is suggested that you do not trim off the excess liner left on the outside of the pool wall, just fold it up under the top rail. |
| Beaded style liners Above Ground Pool Liners have a groove, or lip, all the way around the top edge of the liner. This lip is snapped into a track that runs all the way around the inside of the pool, up at the very top of the pool wall. This track (bead receiver) is what holds the liner in place, and you should be able to see the track if you look up under the top rail on the inside of the pool. |
| For a wrinkle free professional installation See BEADED ABOVE GROUND POOL LINER Instructions provided below. |
| YOU MUST ORDER THE PROPER DEPTH BEADED LINER THAT CORRESPONDS TO THE HEIGHT OF YOUR POOL WALL |
| For a wrinkle free professional installation See BEADED ABOVE GROUND POOL LINER Instructions provided below. |
| YOU MUST ORDER THE PROPER DEPTH BEADED LINER THAT CORRESPONDS TO THE HEIGHT OF YOUR POOL WALL |
| ABOVE GROUND POOL BEADED LINER REPLACEMENT INSTRUCTIONS:
1. Completely drain pool. 2. Remove all wall fittings. (Skimmers and returns) 3. Remove old liner from the pool. 5. Smooth pool floor and fill any depressions with sand. 5. Carefully remove new liner from box and spread it out on a clean dry surface, in order to let it warm up in the sun for at least 1 hour. 6. Insert the bead of the new liner into the bead recepter all the way around the pool. 7. From inside the pool, kick the liner into place so that all sides are against the pool wall and insure that no wrinkles exist. 8. From outside the pool insert a vacuum hose thru the hole in the wall where the skimmer will be attached so that the hose is between the pool wall and the liner. 9. Place tape accross the hole sealing it around the hose. 10. Turn on the vacuum so that all of the air is sucked out and the liner is tight against the pool wall in all areas. (Turn off vacuum and adjust the liner if necessary before proceeding) 11. When satisfied with the lay of the liner, leave the vacuum running and begin filling the pool. 12. Re-install the wall fittings when the water level is just a a few inches below their intended location. |
| ABOVE GROUND POOL BEADED LINER REPLACEMENT INSTRUCTIONS:
1. Completely drain pool. 2. Remove all wall fittings. (Skimmers and returns) 3. Remove old liner from the pool. 5. Smooth pool floor and fill any depressions with sand. 5. Carefully remove new liner from box and spread it out on a clean dry surface, in order to let it warm up in the sun for at least 1 hour. 6. Insert the bead of the new liner into the bead recepter all the way around the pool. 7. From inside the pool, kick the liner into place so that all sides are against the pool wall and insure that no wrinkles exist. 8. From outside the pool insert a vacuum hose thru the hole in the wall where the skimmer will be attached so that the hose is between the pool wall and the liner. 9. Place tape accross the hole sealing it around the hose. 10. Turn on the vacuum so that all of the air is sucked out and the liner is tight against the pool wall in all areas. (Turn off vacuum and adjust the liner if necessary before proceeding) 11. When satisfied with the lay of the liner, leave the vacuum running and begin filling the pool. 12. Re-install the wall fittings when the water level is just a a few inches below their intended location. |
| TIP: Your old Solar Cover makes a great Ground Pad |
| TIP: Your old Solar Cover makes a great Ground Pad |
| TIP: Your old Solar Cover makes a great Ground Pad |
 |
|
|
|
|
|
|
